The No.1 Website for Pro Audio

U 87

Neumann U 87
0 Own It
0 Used It
0 Want It
0 Watch It


The U 87 was designed as a solid-state version of the U 67 tube microphone. It retained the K67-style capsule of the U67, but replaced the tube amplifier circuit with a FET/transformer design. In short, the U87 was a tripolar FET condenser with a transformer-coupled output. A switch below the headbasket allowed selection of Cardioid, Omni, or Figure-8 patterns. U 87i, U 87A iThe mic’s capsule, called the K87, was a center-terminated, dual-backplate, dual-diaphragm 34mm design, like the K67. It differed from the K67 in three acoustically-transparent respects:

  • the K87’s two backplates were electrically isolated from one another,
  • and it therefore connected to the amplifier circuit by four wires rather than three.
  • The capsule mounting screws were “sleeved” to prevent an electrical connection between backplate halves.

These changes were required to support the Figure-8 polar pattern, which otherwise would have required more power than the 48V phantom power supply could provide (without a DC-DC converter).

Note that both the K67 and K87 capsules used a 40-micron spacer between the two backplate halves. In the K67, the spacer is aluminum. In the K87, the spacer is made of (non-conductive) plastic. The K67 (now called K870/67) and K87 capsules are said to be mechanically and acoustically identical.

The K87 capsule was designed for a 60V polarization voltage, but was run in the U87(i) at ~46V; as a result, the U87(i) had ~10mV/Pa lower sensitivity, and 3dB lower signal-to-noise ratio than the AB-powered U77 or the revised U87, called the U87A(i), both of which employed a DC-DC converter to produce a ±60V supply for the capsule.
U 87 i CircuitThe body of the U87(i) housed an optional pair of 22.5V batteries. This space was repurposed to store a DC-DC converter when the U87A(i) was developed in 1986.

The mic’s output impedance was 200Ω. It could be changed to 50Ω by the user; this modification required a solder gun, according to Neumann literature.


What's in your mic locker?

Ribbons Royer R122 (2) Royer R121 (2) Coles 4038 RCA 77-DX (2) RCA BK-11 Large Diaphragm Condensers Neumann U-47 Tube Neumann U-67 Neumann U-87 (2) AKG C414 EB (2) Audio-technica AT4060 (2) Audio-technica AT4033 (2) Shure KSM32 (2) SE Electronics 2200A Small Diaphragm Condensers Neumann KM54 Neumann KM56 Neumann KM264 (2) Schoeps 221B (3) Earthworks TC30K (2) AKG C460 B Audio-technica AT4051 (2) Audio-technica AT4031 (2) Audio-technica AT450 (2) Audio-technica AT825 Audio-technica ATM35 (3) Sennheiser MKH405 (2) Shure SM81 (2) SE Electronics SE1A...

View Post

Warning: Neumann U-87 Scam Alert on Reverb

I purchased a used Neumann U-87 from Music City Pro Audio on Reverb. It had a fake/aftermarket capsule that costs $850 to replace. I didn't know until I sent the mic to be evaluated/serviced by Neumann until 10 months later, well beyond the return period so I have no legal standing. I had...

View Post

Critique my mic list

...KEEP IT) (Shure SM7B - Already own - KEEP IT) CONDENSERS: - Horch RM2J (great 47 style mic) - used vintage Neumann U 87 - Schoeps cmc1 with mk4 x2 (or cmc5 or cmc6), get them used if you could. (Oktava MK-012 x 2 - Already own) Rode NT-2A - Already own - SELL IT Rode NT-1A - Already own -...

View Post


Nobody has reviewed this product yet. Have an opinion?