Hi everyone So we have opened this new sub forum where you can post pictures and words on your electronic DIY build repair and...

Here is a project which should have only been a joystick controller but I got carried away :facepalm: Everything started after...

Dear all, being interested to build some mic, I stumble upon this great simple site: https://store.studio939.com/ Bodies...

I've never done a build diary but since there was interest in the Behringer 2600 thread, I figured why not? This would be my...

hey guys, I thought I'd share a build log of my latest abomination - two Soundcraft 400b input strips in a 1U rack enclosure....

Just built a couple CP5's. They sound good, but when I plug in a Coulour module they no longer pass signal. Also, one of them...

hi everyone! i am planning to build some electret microphone connected and powered to my xlr input with phantom power. the...

Hi everyone, I recently purchased a TAC Scorpion 16:8:2 in mint condition. I've decided to start a quick journal here for the...

So... A friend of mine came with a mic that has gone through a hard accident. Head was destroyed and, upon inspection, so was...

Hello! :) Recently got my hands on an OB-SX, and from then I've been wanting to unlock its full potential. I've had lots of...

Hi guys, Does anyone have soundgrid wsg servers working with hear dante wsg to dante working ? How it performs in studio,...

hi, ive had this dp4+ for a few years but its been in transit from another country so not used it in months, anyway ive always...

¡Hi Geeks! Finally, after four years of research and development (read it learning), four prototypes, many nights without...

Hi, I recently got my first synth and im triyng to do some experimental stuff. I would like to build a fully DIY Spring...

just a few pics of a dbx128 I recapped & modded http://i240.photobucket.com/albums/ff10/doulos24/dbx1181_zps15345c70.jpg...

Hello, I've recently build an ezPDI-500 from Aml. Unfortunatly there is a hum sound that make it unusable. Can hum be caused by...

Sorry if this is in the wrong place, but I didn't see any repair forums. Basically, as the title states, I have a UA DCS that...

whell this small beast have great sound... and since i keeped one of few I had.... i spend some time using it in studio. I...

Solid state Pultec, stereo, Elma stepped rotaries, Original Triad in and output transformers ...and then some...

my latest build based on ssl4000 bus compressor, dual sidechain detector/turbo mode, sidechain HPF, mix n dry mix knob!

Greetings, With the success of the Black Box, the IMT, the Dynatron and the HG-2 under my belt, I decided that it was time for...

Hi guys, I have often seen that for soldering audio gear parts, a 60/40 Rosin Core Solder should be used. My question is...

:cowbell: Hi, I have recently found an interesting thing. Micromodules by Syntaxis - it's Polish company (where I live)....

Hi I have owned these LS-711s since I was 13 ... now I am 42. On these speakers I made my musical history. I don't know how much...

I’m getting bit by the diy bug! So far I’ve done a few synths (on kits and on breadboards), and going to be building a mic...

Hello, I am repairing a Roland R-70 drum machine. It is missing both volume and value sliders and the board for the sliders. ...

You know there are times like these when your life comes to cross-roads, a fork in the road where either the weak-willed walk...

Hi, new to this forum, just picked up a Crest Century VX 52 channel. I took a bit of a punt on this one as it's without its...

Goal: boost CV signal from sequencer by 20~100mV. Hello I'm trying to design a circuit that would add approximately 20~100mV to...

Hi guys, I just picked up a really cheap GT66 with a faulty power supply, it seems the unit was dropped and the transformer...

Hi all, I was thinking of putting my thoughts on this site while embarking on a journey with a project was perhaps a good...

Hey there guys, replacing a Sterling ST-69 capsule that I busted... any thoughts on these guys here? I’ve got plenty of nicer...

Hello Everyone, I've put together a DIY talkbox using a Monacor KU-516 horn driver (160-6,500 Hz frequency range), a...

Dear, All Recently, I got vintage QuadEight Equalizer(EQ-444) without PSU. So I made original PSU.(+-15V,+-28V) But it...

After trying a radial jdi duplex in my synth studio and thinking "damn this thing sounds great- i wish it had more...

I have Peavey Valveking 112. The manual I downloaded says and shows in images “Minimum 16 ohms” by the external speaker jack....

Hi got the Superlux HI10 mic. I wanted to open it, in order to see if possible to make some mod. But, there are 3 wires are...

Calling the brains... Do any of you smart people happen to know if the 24/48V PSU from BAE that is supplied with their 6 unit...

hi guys, i just bought an old dynamix 3000 console and i want to improve the sound of the preamps and eq´s. The desk is...

Need a 1.4 Q +10 dB Bell at 20 Hz passive EQ box allowing both line-level and HP out inputs and driving Sneeheiser HD580\600\650...

Hello Geekslutz, Newbie and hack from Japan here. Was fortunate enough to acquire a Soundcraft Spirit FX16 that was about to be...

Just scored another Soundcraft yesterday. This one was sold as not-functioning. Got it for very cheap. It's a 18/8/2...

Just wanted to share a controller that I made for my JU-06A Here is the trick. I used these 3 videos from Notes & Volts as...

I've been needing something like the Roland A880 for a very long time, but they were always so ridiculously overpriced. This...

Hey guys I video'ed my latest kit build, I thought I'd post it here. I didn't do much commentary or anything, I just sped...

Hi guys! Long-time lurker, first-time poster. I built my first op amp, a GAR2520, to replace the ones in my Warm 412...

Hello fellow gear slutz and gurus. I seen another thread on a modification for the DBX 163X. I decided to touch up on the same...

I bought this a couple of years back and it sounds great! Really nice when driven from synths, drums and Rhodes - it's just a bit...

Oooh, I've been a member for a week, and only now do I see this forum? I must be blind. It's not a photo diary, but maybe a video...

Hello! To expand the aux sends on my Audient 2802: I would like to build a great quality 16 input line level 4 aux send...