Hi everyone So we have opened this new sub forum where you can post pictures and words on your electronic DIY build repair and...

Good day. Newbie here. I'm the host of a syndicated radio program that is leaving the nest and protection of our flagship station...

hi guys, i just bought an old dynamix 3000 console and i want to improve the sound of the preamps and eq´s. The desk is...

Dear, All Recently, I got vintage QuadEight Equalizer(EQ-444) without PSU. So I made original PSU.(+-15V,+-28V) But it...

Hi. I need this part PCM53 JG - I to repair a PCM60 but i don't found for buy. Can help me?

Hello, Since starting this thread: Roland JV-880 No Audio I have aquired a nice soldering station and have been repairing...

So I have a really cool idea that involves a tap handle for sound control, as I have been searching in the potentiometer...

Hey Gang, I ran out of patience waiting for the case for this monster so I've decided to power it on and test it. Runs like a...

whell this small beast have great sound... and since i keeped one of few I had.... i spend some time using it in studio. I...

Hi guys I have owned samplers for years now and I am getting into the world of DIY devices (based on tiny computers such as...

Hello, all. This week I picked up a DBX 163A for cheap. I set to changing out the caps because some of the electrolytics were...

Hi all, first post and not 100% sure if it’s the right forum, couldn’t find anything on this exact topic. In my mic...

Hi, (total electronics n00b) what is the circuit for signal to analogue VU ? eg: a line level (send etc.) to VU...

BLA ADA8000 Premium Mod vs Apogee Ensemble Test - BOTH are clocked by a BIG BEN OK, this will just be my opinion. Sorry, no...

(pictures to come) So last week I decided to really, truly, this time rewire my rack gear (again). So I pulled all the gear...

Hello Geekslutz, Newbie and hack from Japan here. Was fortunate enough to acquire a Soundcraft Spirit FX16 that was about to be...

Hello everyone! I'm not really sure which category my question belongs to, but whatever. I need a kind of MIDI pad controller...

Hello fellow gear slutz and gurus. I seen another thread on a modification for the DBX 163X. I decided to touch up on the same...

¡Hi Geeks! Finally, after four years of research and development (read it learning), four prototypes, many nights without...

I purchased two “U87 clones” at “Mic And Mod”. I assembled and tested two microphones, but there is noise in one of...

Greetings, Check out this upload I did of me building the Rangemaster on the cheap. I fully understand that most of you could...

The Nova Desktop should get an update/mod package to shove its circuitry off edge.Is it possible to expand the the voices or add...

I saw similar threads but none that exactly answer my question. I want to build something like...

Hey. I'm a real novice so go easy on me! I have plenty of components to make a passive mixer for my modular synth, I just...

Wanted to share this mod to fix the slide pots on a UREI 535 EQ. I have 3 of these and all 3 have been upgraded with this kit....

Hi everybody, I am planning to clone the Tascam RC-416 remote for the Tascam MSR-16 Tape machine for myself. But I thought that...

Is it relyable to build a mini summing box (passive mixer) with 2 in for left and 2 in for right audio in and oun couple of...

Hey guys, modding a DBX 163x (also would aplly to Aphex651), C2 is replaced with a recommended Panasonic EXC-ELSA39 Ferrite bead...

Hello! My girlfriend has given me a USB powered turntable which only has a line level output, with no RIAA eq. (the entire...

Hi. I already posted this over at GroupDIY, but I’m not familiar with the forum and i feel totally clueless. Anyway, I have...

Hi all, I was thinking of putting my thoughts on this site while embarking on a journey with a project was perhaps a good...

Hey Guys recently got finished on a mod/upgrade for my PRE73 Mark I which i think was from the 2nd or so shipment of these pre's,...

Hi All Does anybody know where I could find a sound similar to the intro (12 seconds in) to Sirius by The Alan Parsons Project...

Hi everyone, I recently purchased a TAC Scorpion 16:8:2 in mint condition. I've decided to start a quick journal here for the...

Hi, I’ve recently finished building a guitar amp in the shape of the head of medusa... made a little documentary about it,...

Heya guys, I wanted to know if there is any place I could obtain part replacements - like the silicone pads for the BOSS DR 660....

I was talking recently to an engineer I know and respect, and whilst talking about drums he mentioned that he pretty much never...

Hi, I'm trying to install a Minerva Mod in my Juno60 but am stuck on one of the first steps. Right at the beginning, after...

I want to make a HPF 80hz 12db per octave HPF. For a mic pre. I take it I would run this right after the mic pre. Not lnline...

I’ve acquired this speaker for free and am trying to fix it up. I know just enough about this sort of thing to be dangerous...

New toys..... Finally had my LA3A 500's built... Long project but its nice to see them finally finished. Did some custom work to...

Just scored another Soundcraft yesterday. This one was sold as not-functioning. Got it for very cheap. It's a 18/8/2...

This is a mod I did to the Symetrix 528 first i bought it "modded" and it had the daughter board for the mic pre...

Much have been said on this cheap, yet professional opamp. There are many manufacturers version of this chip. A popular...

here is a pic of a alesis 3630 Mod im working on for the Rev D boards....

just a few pics of a dbx128 I recapped & modded http://i240.photobucket.com/albums/ff10/doulos24/dbx1181_zps15345c70.jpg...

So I recently acquired a DX9 which is not entirely functional. It mostly makes weird static/sine noises. When I opened up the...

Hello, I am repairing a Roland R-70 drum machine. It is missing both volume and value sliders and the board for the sliders. ...

I am restoring a 75 MCI JH-100 and looking for some parts .... starting with power cord.. I know it’s standard but round female...

I just scored an Ampex MM-1100 16 track tape machine and need some help sourcing parts. it came with all the good back up stuff...

Electro Harmonix 12AY7 Mic Pre Amp Modifications As I have noted a fair number of comments on the Internet, on problems and...