The No.1 Website for Pro Audio
 Search This Thread  Search This Forum  Search Reviews  Search Gear Database  Search Gear for sale  Search Gearslutz Go Advanced
Soundcraft 200B project form a designers point of view.
Old 25th January 2019
  #91
Gear Maniac
 

Chips! I forgot to include the types of the small signal transistors.

I used the 2SC2389 and the 2SA1038. Both 50 m.a transistors.
They aren't in production anymore.
I think the KSA 992 and the KSC1845 would be perfect too.

For the headers I used MOLEX 3 pin with spacing 2/10 inch.
I use soldering for connection: better than the female part that goes with the male part on the PCB.

For the drivers T7&T8 it would be better to use the 2SC2705(Y) and the 2SA1145(Y) for dissipation reasons. Unfortunately both not in production anymore. If you want to look yourself for replacement of these "elongated TO92" transistors look for a low Cob and low current capability.

It is really a shame that many outstanding transistors like the last mentioned are not produced anymore.

Of course I have many hundreds lying around here, but I would't like to add an commercial aspect to this. (perhaps not allowed here also)
Old 25th January 2019
  #92
Gear Maniac
 

Some more about the regulator: The focal point was to get a good PSRR and a regulator that is "at ease" with the load at it's output.
I didn't want capacitors or elcaps have an influence on the sound, so safe for the 33pF it doesn't uses any elcaps in the regulator.

About the raw power supply for lets say the 1.2A maximum: first elcaps pair 10,000 mu would be more than enough, 4.700 could be used too I guess.(the latter only when using chokes) As for the transformer I would recommend an old fashioned E I core lamination transformer, preferably with two winding chambers.
Use fast soft recovery diodes. Do NOT use decoupling caps over the elcaps.
Using a choke the second pair of elcaps could be in the same ball park as mentioned values.
Old 25th January 2019
  #93
Lives for gear
 

Interesting. So 1.2 A @ +/- 17.5V is the maximum for this supply?
Old 25th January 2019
  #94
Gear Maniac
 

The power supply in this shape and form yes.

Provided enough cooling for the serial devices and lowering the 0.5R to about 0.25R the power supply could deliver 2A.
Dissipation in the 0.25R will call for a 2W device.

Higher voltages would also be possible changing resistor values.
Old 25th January 2019
  #95
Gear Maniac
 

Try to upload a better picture of the schematics
Attached Thumbnails
Soundcraft 200B project form a designers point of view.-sr1-new1.jpg  
Old 25th January 2019
  #96
Gear Maniac
 

Raising (or lowering) output voltage:

Let's say output voltage increases with 20%, you raise R2/R16/R28 and R1/R20/R27 with about the same amount of percentage.

Output current is solely depended on the R6 and R7 "current sensing" resistors. Lower the same amount as the % of higher wanted maximum current output.

T7 and T8 dissipation will be higher with higher current and voltage, so 300 mW will be often not enough, use 800 mW or so in these cases. and of course you will have to pay attention to the dissipation of the series TO220 device (transistor), including watching the max. current specs of this transistor.
Old 27th January 2019
  #97
Gear Maniac
 

As I haven't looked into this regulator for a couple of years, I decided to have a closer look again doing some computer simulation in MicroCap 9 pro.
+3dB point of the PSRR of an LM317 regulator is about 2.2 KHz, from this regulator somewhat above 100KHz...
Peak in phase shift between input and output are 15 KHz and 1.2 MHz respectively.

Furthermore: the base current of the serial transistor subtracts of course from the current of the current source providing the bias for the driver transistor. So when using larger output currents R3 and R4 may have to been lowered to provide the right bias current for the driver transistor.

If the power supply isn't loaded all the current from the bias current source (D2, T1, R4 for the positive side) flows through T8. This will lead to roughly 160 mW in dissipation. So, after all it would be possible to use 300 mW transistors for T8 and T7, even if we lower R3 and R4 to remain enough bias at larger output currents than 1A.
Post Reply

Welcome to the Gearslutz Pro Audio Community!

Registration benefits include:
  • The ability to reply to and create new discussions
  • Access to members-only giveaways & competitions
  • Interact with VIP industry experts in our guest Q&As
  • Access to members-only sub forum discussions
  • Access to members-only Chat Room
  • Get INSTANT ACCESS to the world's best private pro audio Classifieds for only USD $20/year
  • Promote your eBay auctions and Reverb.com listings for free
  • Remove this message!
You need an account to post a reply. Create a username and password below and an account will be created and your post entered.


 
 
Slide to join now Processing…
Thread Tools
Search this Thread
Search this Thread:

Advanced Search
Forum Jump
Forum Jump