hello, some audio interfaces or synths specify an output or input for stereo signal with only one 1/4" UNBALANCED TRS,...

djcandu

I need a new vocal mic stand for studio use (preferrably with a boom) sturdy enough to use with a decent condenser (faux U67...

Suntower

Hi all, I’m considering purchasing the Genelec 8351’s. I’m currently coming out my dangerous source analog XLR to my...

orangefridge

Hello, Would someone be king enough to giveme the inner dimensions of an original Neumann U87 wooden box? I need inner...

fredpg

I've got some van damme XKE instr. cable that has this hard thermoplastic shield round the signal wire. It's conductive, but I'm...

Quetz

Hi, i have an old czech Tesla Cobra Mic. the connector is 3 pin, but unlike an xlr…. The upper two Pins are too...

Buballakov

Hey all. I have a Tascam 238 (old 8 track cassette recorder) with 8 RCA line level inputs and 8 RCA line level outputs. The...

Banana Brains

Hello, guys. My friends will be gigging next week and I am helping them with technical stuff. They need to connect their audio...

Ez Presso

Hi, slutter here: Looking at a solution for close micing a 6-piece drum kit. Ride, two crashes, high hats, all have close...

slutter

I just bought an old Sony MXP21 mixer on a lark for $100 to consolidate some input channels from my various synthesizers. I have...

beachbuminthesun

I acquired a ev 664 mic and tried to attach it to my standard microphone stand but it just slips over it, it seems slightly too...

greengiant

I found a proper and courteous answer from a colleague.

optofonik

Hello everyone. I got my first vintage tape machine Saba 300S but I am a bit confused on how to plug it into my soundcard since...

eftihis

I have an old IVL midi interface that accepts an 8-pin midi cable from the pickup. I have been looking everywhere but cannot find...

pacaruso

I'm buying a pair of monitors and an interface (prob. zoom uac-2) that i'm going to connect to my pc. I also need to connect my...

yellow_matter

To start I'm new to this website and this type of work so excuse any errors in this post, this website just seemed like the...

mattbutt

I need new cables because i just bought a patch bay... i already have Mogami Gold (balanced 2534, the ones you can buy at...

petecho

I have a Radial Hot Shot pedal that works fine. It sits too high on my pedal board and I want to DIY a switch like the hotshot...

wonderlover

I am soldering my studio wiring and I am new to soldering and taking time. So far, everything went well. I even managed to solder...

FriFlo

I am looking to move my noisy computer to my walk in closet that's about 17ft away. The Digilink cable I have for my Omni HD...

edaub1

Hey guys, I was looking to buy the Audient ID22. Until now I had been using my Line6 POD HD500X as my main sound card.(It...

Ishaan Kunwar

Hi, that's my first post, hope it's the right section of the forum. I searched for similar threads, but they're too old. I...

demedex

For anyone that uses the Tascam PB664 patchbay, attached here is a template I created for the bay that works pretty well. kfhkh

mrbutterskin

Hello everyone, I looked in the forum but I did not find anything about it, I hope you can help me. I wanted to know if any of...

bender87

I need a bunch of cables to go between my synths and mixer/audio interface for a home studio (3m/10ft should probably do, witha ...

rhythmcomposer

Hi all, I am looking for two 3/4" connector cables for the DSI OB-6 Desktop module. The outputs on the unit are unbalanced...

191919

Hi, ok, this is a very special question. The LED PSU of our D-Control ist broken, resistor R17 is burned and I cant see any...

kabelton

Hey all, I’m wiring up a pair of redco panels - xlr m/f using Mogami 2934 16 channel snake. I’ve got the wires tinned, the...

DaveNJ

Hello folks, Quick question if some could be so kind : If I have an SPDIF output which I want to hook up to a 110ohm...

woodnut

Please forgive the potentially idiotic question but I'm really struggling with this and some expert advice would be greatly...

LemonMoose

Hey guys, I need new cables for my mixbus in and out of my adda. I've been using Klotz and Mogami and they sound almost...

MatsNo

Hey guys, I'm using my very simple turntable to record vinyls into my DAW. My setup works but I struggle to understand...

eden1108

Hi All, I see these "JDS Promotions" patch cables on ebay all the time and I was curious if any Gearslutz have had...

Stuart White

Hi All I wonder if you could help. I've acquired a vintage Philips LFH 0186 Dictaphone and I'm looking to digitize the some...

gavfreed

Hello everyone, I am moving overseas and would like to know the best (hopefully on cheaper side) way of transporting my setup....

keevoskates

Hello, I have two vocal mics in my room, and will only be using one at a time. Instead of swapping cables in and out of the back...

compo

Assistance please... I have an mpc 2000, a yamaha daw 16-track board w/ cd burner installed in it, two krk monitors. That’s...

imnotyofriend

Anyone using these for AES duties? How do you find them for analog over other cables? I use Mogami 2549 and 3173 and would love...

zoom25

Hi guys, I am running a Behringer P16-I in control room to a P16-M in my booth and wondering about the cat 5 cabling. If I...

Simon Xang

How you doing Slutz :) My first post here but a long time lurker. Appreciate all the great information on this site. It has...

Kriston3107

I've read whatever threads there are on here about whether or not using the "digital" Mogami cable improves the sound...

Obe1

Hey everyone! For the first time, I'm attempting to run a compressor via the insert in my TOFT ATB24. I'm using a TRS Y Cable....

thetruevine

I have an old Yamaha PSS-270, my very first keyboard from 1987 (original box and all). Can't bear to part with it, lol. Works...

Journeygirl

Hello, I just bought online a new Yamaha P-45 digital piano. It is on the way, I have not received it yet. I was reading on...

javierj

Hi there, I've had this niggling issues for a while now and it is starting to really annoy me. My set up is as follows: PC...

danyjr

Hi All, Have a Neve BTC V55 series broadcast console that I am restoring, but the tech manuals were lost. I have the...

Stevesteve50

This seems very strange. I have a pair of Adam A7Xs connected to an Apollo 8 with a pair of Monoprice Premier XLR - TRS cables....

calzone

There're wood available for almost every synth out there yet I couldn't find anything for the Pioneer/Dave Smith AS-1. Not even a...

The_Champ

Hi, Please see photo attached - may I connect the setup like this? So the question is - may I use both outputs (XLR AND TRS)...

simnik12zh

I have a launchkey and am using it with Logic over USB. I have all the faders, knobs, buttons, etc mapped to specific things in...

callumhoskin