insert cables on an old school compressor

terrytee · 30th November 2007, 02:20 PM

ok i got a peace of shit compressor given to me its call LPB S-2, its popped up on this forum a few years ago and didn't get a standing ovation. Anyway it cost me nothing so i don't care if it ends up sounding like a wight light i still wanna get it up and running.

My question is this how do i wire up an insert cable to it?

The back of the unit has screw pots for the following.

COMP STRAP

OUTPUT R
OUTPUT T

GND

INPUT R
INPUT T

BR

My insert cables, when stripped down, has 2 wires in input and 2 in output ,one of which is incased in a plastic coating, black on the output white on the input.

If this is a novice question i should point out that i am a Musician first, a dick-head second and a electrician/engineer last.

tINY · 1st December 2007, 08:19 AM

I don't know for sure, but it looks like there are connections for Ring and Tip on input and output.

GND is pretty obvious - ground.

COMP STRAP sounds like it the input to the control on the compressor - I'd guess that you use it by connecting it to the input "T" or a side chain.

I have no clue what BR would be....

-tINY

terrytee · 1st December 2007, 11:18 AM

thanks for info Tiny i will take what you said on board and give it another try.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Setting up a hardware compressor as an insert in pro tools??	EspionageWHW	Rap + Hip Hop engineering & production	9	27th January 2007 12:56 PM
Compressor sidechain insert applications	Tim Farrant	So much gear, so little time!	2	11th October 2006 09:13 PM
can I highend compressor, used as an insert be enough for the whole mix?..	activexjava	Music computers	5	18th April 2006 02:45 PM
can an Insert harware compressor replace plugins .. i.e just using a stereo unit	activexjava	High end	5	15th April 2006 08:55 AM

30th November 2007, 02:20 PM	#1
terrytee Lives for gear Join Date: Oct 2007 Posts: 757	insert cables on an old school compressor ok i got a peace of shit compressor given to me its call LPB S-2, its popped up on this forum a few years ago and didn't get a standing ovation. Anyway it cost me nothing so i don't care if it ends up sounding like a wight light i still wanna get it up and running. My question is this how do i wire up an insert cable to it? The back of the unit has screw pots for the following. COMP STRAP OUTPUT R OUTPUT T GND INPUT R INPUT T BR My insert cables, when stripped down, has 2 wires in input and 2 in output ,one of which is incased in a plastic coating, black on the output white on the input. If this is a novice question i should point out that i am a Musician first, a dick-head second and a electrician/engineer last. __________________ Lookin at my Gucci it's about that time........

1st December 2007, 11:18 AM	#3
terrytee Lives for gear Join Date: Oct 2007 Posts: 757	thanks for info Tiny i will take what you said on board and give it another try. __________________ Lookin at my Gucci it's about that time........

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes	Rate This Thread
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode	Rate This Thread:

1st December 2007, 08:19 AM	#2
tINY Lives for gear Join Date: Jul 2004 Location: Orygun Posts: 5,835	I don't know for sure, but it looks like there are connections for Ring and Tip on input and output. GND is pretty obvious - ground. COMP STRAP sounds like it the input to the control on the compressor - I'd guess that you use it by connecting it to the input "T" or a side chain. I have no clue what BR would be.... -tINY