All Advertisers
| All Advertisers |
| |||||||
Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Source for a Timeline Lynx I manual? | mlocascio | High end | 6 | 22nd January 2006 09:58 AM |
| Anyone know a good place to buy cables? Specifically digital cables? | sleepwalker | Music computers | 4 | 26th February 2005 03:37 PM |
 |
| | Thread Tools | Search this Thread | Rate Thread | Display Modes |
12th April 2006, 01:33 AM
| #1 |
| Gear Head Join Date: Jan 2006 Location: St. Paul, Minnesota USA
Posts: 47
| How to build/buy sync cables for Lynx timeline I have a pair of Lynx timelines that will help me slave my JH-110 1" 8track to Pro Tools HD. Unfortunately there were no cables or manual with the units. The units seem to power up and all buttons work. Does anyone out there know where I can find diagrams to build the cables? I am good with soldering and following directions, I built several D.I.Y. contraptions The (MCI) JH-110 has the remote, so how do I get it all to work? Thanks! |
|  |
|
12th April 2006, 07:55 AM
| #2 |
| Lives for gear  Join Date: May 2005 Location: Oklahoma City
Posts: 1,022
| |
|
| |
|
12th April 2006, 08:46 AM
| #3 |
| Gear Head Join Date: Jan 2006 Location: St. Paul, Minnesota USA
Posts: 47
| Thanks Brian. I can gleen some pin assignents from those data sheets, but how does the flow go? One manual page refers to a "Y" cable. Do I find a M/F block connector to tap in between the controller and the deck? |
|
| |
|
13th April 2006, 10:36 AM
| #4 |
| Lives for gear Join Date: May 2005 Location: Oklahoma City
Posts: 1,022
| Hmmm..I just knew there were various cable pinouts listed at the site I linked. Which page are you examing? Bri |
|
| |
|
15th April 2006, 12:05 AM
| #5 |
| Gear Head Join Date: Jan 2006 Location: St. Paul, Minnesota USA
Posts: 47
| I can see that there is a lot of wiring involved, I have some of the connectors necessary, the Cinch Jones are available from Mouser, I was wondering how my remote would connect (if at all) once this wiring harness replaced my remote wiring. Could you then control the machine functions from Pro Tools? Anyone ever try this? |
|
| |
|
15th April 2006, 12:58 AM
| #6 |
| Lives for gear Join Date: Oct 2004 Location: Burbank, CA, USA
Posts: 707
| The MCI decks only had one remote connector so if you want to use an existing remote mode AND a synchronizer, you need the Y cable. Also, you'll probably also need to cut jumpers inside the MCI remote. If you can't find that info, I've got it somewhere. Either way, you're right -- it's a lot of wiring!
__________________ http://studioelectronics.biz Service & Restoration of UREI dbx Eventide Marshall AMS Tube Gear and more |
|
| |
|
15th April 2006, 06:14 AM
| #7 |
| Gear Head Join Date: Jan 2006 Location: St. Paul, Minnesota USA
Posts: 47
| Thank you Brian and David. If anyone trips across any info (that isn't on-line) in your searches that pertains, I would be thrilled to archive, use, and save for the next person. I would be glad to cover any cost involved with getting it to me. So many projects, so little time! This is a great site, I just discovered it a few months ago. I really enjoy it a lot. Carry on. |
|
| |
|
15th April 2006, 11:25 AM
| #8 |
| Lives for gear Join Date: May 2005 Location: Oklahoma City
Posts: 1,022
| Various Lynx hookups on file here, but no "archives" for other combos besides Otari plus Sony. Bri |
|
| |
|
8th August 2008, 04:51 PM
| #9 | |
| Gear interested Join Date: Aug 2008
Posts: 1
| Looking for wiring info on MCI JH-24 to Lynx unit? Quote:
Did you find the wiring diagramss for a Lynx to JH-24? I am in search for the correct connections. Thanks. Malcolm Harper 512 312-1610 malcolmh@austin.rr.com | |
|
| |
|
| Bookmarks |
| Thread Tools | Search this Thread |
| Display Modes | Rate This Thread |
| |
Linear Mode
